In detail. P-BUS System Monitor PSM3.

  • One monitor for (almost) everything – replaces separate displays for battery, tank, temperature, main switch and loads
  • No configuration software needed – setup and expansion are done directly on the touchscreen
  • Data recording to SD card, even in standby, for later analysis on a PC
  • Alarm list for empty batteries, over/undervoltage and full or empty tanks, optionally with an audible signal
  • Compact panel cut-out (88 x 88 mm) fits common switch panel cut-outs
  • Runs offline: own software, running locally on the display, without internet and independent of Android and iOS

P-Bus terminators included: All required P-Bus terminators are supplied. You only need to add the matching P-Bus cables.

The philippi P-BUS System Monitor PSM3 is more than a battery or tank monitor: depending on which P-BUS components are installed in the on-board system, it automatically shows the matching menus. Seven sub-menus cover batteries, tanks, temperatures, AC/DC energy flow, main switches, loads and bilge pumps, giving skippers and outfitters a complete overview of the on-board electrics at all times.

Configuration is done entirely interactively on the monitor itself; no additional computer or tablet is required. Several PSM3 units can be installed at different locations on board and show the P-BUS data synchronously – practical for both cockpit and navigation station. The philippi PSM3 is supplied with an M12 T-cable and both P-BUS terminators, so the initial installation is possible without ordering anything else.

Compatibility.

The philippi PSM3 is part of the P-BUS system and works with other philippi components: SHX/SHC battery management shunt for battery monitoring, CMT3 tank interface for tank display, FHC or TSC main switch interface, CMR4 universal relay module for switching and dimming loads, TPC temperature interface and SHX-L, ACE, DCB, LAU, CAV and DCW for the energy flow display of DC and AC systems, including Studer and Mastervolt inverters.

Original equipment quality

  • Individually tested: every unit is connected and tested in a test environment in Remseck.
  • Brand-name components, as in series production for boatyards.
  • Repairable for decades: spare parts up to 30 years back, own repair centre.
How we manufacture

Technical data

Operating voltage8–64 V DC
Current draw60 mA, standby 2 mA @ 12 V
Display3.5" TFT graphic display with glass touchscreen
DimensionsL 105 x W 105 x D 35 mm
Panel cut-out88 x 88 mm
Data recordingSD card, also in standby
Scope of deliveryM12 T-cable, 2x P-BUS terminator

Manufacturer and product safety

philippi elektrische systeme GmbH
Neckaraue 19
71686 Remseck am Neckar
Germany
info@philippi-online.de

Safety information: see the operating manual and data sheet.

Frequently asked questions. Answered briefly.

Do I need to configure the PSM3 with a computer?

No. The PSM3 is set up and expanded entirely interactively on the touchscreen; no computer, tablet or configuration software is needed. The monitor detects the connected P-BUS components and automatically shows the matching menus, for example for batteries, tanks, temperatures, energy flow, main switches, loads and bilge pumps.

What is included with the PSM3?

The PSM3 is supplied with an M12 T-cable and both P-BUS terminators. This makes the initial installation possible without ordering anything else. You only need the matching P-BUS cables to connect the monitor to the other components, such as the SHX shunt or the CMT3 tank interface.

Does the PSM3 show menus for which no sensors are connected?

No. The PSM3 adapts automatically to the connected P-BUS components and only shows menus for which data is actually available. If, for example, no tank interface is installed, no tank display appears. If the on-board system is later extended with further components, the display can be expanded directly on the touchscreen.

Can I use several PSM3 units on board at the same time?

Yes. Several PSM3 units can be installed at different locations on board and show the P-BUS data synchronously, for example at the navigation station and in the cockpit. Each monitor fits an 88 x 88 mm panel cut-out and draws 60 mA, only 2 mA at 12 V in standby.

Can the PSM3 record data?

Yes. The PSM3 records data to an SD card, even in standby, for later analysis on a PC. The monitor also keeps an alarm list for empty batteries, over- and undervoltage and full or empty tanks, optionally with an audible signal. This lets you keep track of events that occurred while you were away.

Goes well with it. Accessories and add-ons.

philippi P-BUS secondary monitor PSS, 2.4-inch touchscreen
philippi

P-BUS Daughter Monitor PSS

229,00 €
philippi P-Bus AC interface CAV
philippi

P-Bus AC Interface CAV

179,00 €
philippi P-Bus temperature interface TPC 4
philippi

P-Bus Temperature Interface TPC 4

179,00 €
philippi temperature sensor TEMP-BT
philippi

Temperature sensor TEMP-BT

19,90 €
philippi P-Bus tank interface CMT3
philippi

P-Bus Tank Interface CMT3

185,00 €

Prefer a quick chat?

Tell us what you are planning. We will tell you honestly what you need and what you don’t.

Beratung bei philippi in Remseck am Neckar