Offline.
All functions run locally, without internet or cloud.
See battery, tanks and energy flow. Control fridge, heating and lights. With the PSU, switch, protect and measure every circuit.
479,00 € incl. VAT · Made in Germany
Tanks and temperature. Up to 4 tanks and 2 temperature sensors directly on the display.
12 and 24 V. For both system voltages and all common battery types.
CI and CAN bus. Integrated in the display, no additional modules.
Offline. All functions run locally in the vehicle or on board, without internet.
Our own software. Developed by philippi, runs locally on the display and without an app.
Demo
Tap through overview, battery, tanks, energy flow and loads, just as you will later on the display in your motorhome, van or on board.
In detail
Overview. Battery, energy, tanks and switches on one screen: you see the state of charge, solar yield of the last 24 hours, fresh and waste water levels and switch states at a glance.
Energy flow. Solar, DC-DC charger, shore power and battery in one picture: you see the current of each source in amps and immediately where the energy comes from and where it goes.
Battery history. For each battery you see the state of charge, temperature and the voltage of the individual cells. A chart shows the history over 30 days.
Solar history. Solar yield as a chart in watts, for 3 hours, 24 hours or 3 days. You also see the energy generated in kWh and the peak power.
Control devices. Operate the cool box and heating directly on the display: set the temperature, choose the operating mode and fan speed, and switch the heating between diesel and electric.
Control and monitor loads. Each load shows its switching state and current, for example cool box, water heater and water pump. With the PSU you switch it with a tap on the display.
Switch and dim lights. With the PSU you switch and dim every lighting group to the exact percentage on the display, for example spots, ambient, dinette and bathroom. Classic push buttons still work too.
BullTron Polar batteries connect directly via P-BUS, without an additional shunt. The PCU shows state of charge, current, cell voltages and temperature for each battery.
View BullTron batteries
With the Smart Interface SMI you connect Victron inverter/chargers and solar charge controllers (MPPT). Via Wi-Fi or Ethernet the data also goes to the free philippi app.
View Smart Interface
Tank sensors, shunts and batteries connect tool-free to the Connect Hub. Only a single 10 m cable runs to the display.
View Connect HubComparison
|
|
|
|
|---|---|---|---|
| Touch display, 144 × 90 mm | |||
| ✓ | ✓ | ✓ | ✓ |
| Battery: state of charge, voltage, current, temperature | |||
| ✓ | ✓ | ✓ | ✓ |
| Tanks and temperature directly on the display | |||
| ✓ | ✓ | ✓ | ✓ |
| Energy flow and solar yield | |||
| ✓ | ✓ | ✓ | ✓ |
| Control fridge, heating, air conditioning (CI/CAN bus) | |||
| ✓ | ✓ | ✓ | ✓ |
| Connect sensors without tools, one cable (10 m) to the display | |||
| – | ✓ | ✓ | ✓ |
| Switch and dim circuits | |||
| – | – | 8 outputs | 8 outputs |
| Electronic protection per output | |||
| – | – | in 5 A steps | in 5 A steps |
| Measure current per load (8-way shunt) | |||
| – | – | ✓ | ✓ |
| Drive motors, pumps, valves (H-bridge) | |||
| – | – | ✓ | ✓ |
| Integrate Victron inverter-chargers and MPPT | |||
| – | – | – | ✓ |
| Remote monitoring with the philippi app | |||
| – | – | – | ✓ |
| System voltage | |||
| 12 / 24 V | 12 / 24 V | 12 / 24 V | 12 / 24 V, SMI: DC 8–16 V |
All combinations are based on the PCU. Connect Hub, PSU and Smart Interface are extensions and available individually.
Products
Platform
All functions run locally, without internet or cloud.
The software is continuously maintained.
BullTron, Votronic, SuperB, SuperSense, Dometic, Timberline, Truma.
Already in use in over 1,000 on-board electrical systems.
We have been developing monitors for on-board monitoring for over 20 years.
Advice from Remseck, also for older philippi devices.
Order
The PCU comes with the display and the basic components required for operation. If you have questions about installation and compatibility, we'll advise you personally.
The PCU (philippi Control Unit) is the central control and monitoring unit for the onboard electrics in campers, motorhomes and boats. It combines battery, tank and energy monitoring as well as load control on a single display. This lets you keep an eye on the entire onboard system without switching between several displays.
The PCU alone shows battery, tanks and energy flow and controls fridge, heating and air conditioning. With the Connect Hub, only one cable runs to the display. The PSU adds eight protected outputs that can be switched and dimmed, with current measurement. The Smart Interface SMI integrates Victron devices and sends the data to the philippi app.
The PCU shows the state of charge, current and voltage of your batteries, the levels of up to four tanks and the complete energy flow from solar, inverter, DC-DC charger and shore power in real time. You can see at any time where energy comes from, where it flows and how long the battery will last at current consumption.
Yes. The PCU is compatible with both 12 V and 24 V systems and can be used regardless of the voltage of your vehicle or boat. This makes it suitable for the classic 12 V camper as well as for larger expedition vehicles, truck conversions or yachts with a 24 V system, without a separate version being required.
Yes, with the Smart Interface SMI. It transmits the on-board system data via Wi-Fi or Ethernet in real time to the free philippi app for smartphone and tablet, for example while laid up for winter or at anchor overnight. The PCU itself works locally and does not need the internet for its functions.
The PCU costs 479,00 € including VAT, with or without a frame. Within Germany, shipping is free from an order value of €250; delivery time is 3–5 working days. Included are the display and the basic components required for operation. Connect Hub, PSU Switching Unit and Smart Interface are available separately.