philippi Academy · Measure and Monitor
Retrofitting a tank gauge: sender, display, wiring and common faults
In short
You retrofit a tank gauge in three steps: choose a tank sender to suit the medium and tank, choose a display that understands its signal, and run signal and ground wires cleanly. Float senders with 10 to 180 ohms suit most displays. The philippi PCU shows up to four tanks directly at the display, without a tank module.
Retrofitting a tank gauge means making three decisions: which tank sender fits the tank, which display understands its signal, and how signal and ground reach the display cleanly. Keep to this order and you order correctly the first time, on a boat as well as in an expedition vehicle or motorhome.
Step 1: choose the tank sender
The sender depends on the medium, the tank shape and access to the tank. In short:
| Sender | Principle | Suitable for | Installation |
|---|---|---|---|
| TGW / TGT | float, 10–180 ohms | water, waste water, fuel; not for black water | from above |
| TDS / TDN 200, TDT | hydrostatic pressure | all media including black water, tanks up to about 2 m | from above to the bottom |
| UTV | ultrasonic, contactless | water, waste water, black water; not for fuel | from above, 2.5 cm dead zone |
| Gobius C | radar from outside | plastic tanks without drilling | outside the tank |
All details, including tank shape and dead zone: Which tank sender suits my tank.
Step 2: choose the display
Sender and display must speak the same signal type. The philippi tank senders connect directly to the BTM2 and VTM 2 monitors and the PCU, without an additional interface. The P-BUS system monitors PSM3 and PSL need the CMT3 tank interface for this. All displays at a glance: battery and tank monitors.
- Only view tanks: a tank monitor such as the VTM 2.
- Battery and tanks together: the BTM2 battery and tank monitor.
- Battery, tanks, devices and lights on one display: the PCU. It measures up to four tank senders and two temperature sensors directly at the display and also operates heater, fridge and air conditioning via CI and CAN bus. It switches lights and loads with the PSU.
Step 3: connect and set up
- Check the internal height, the hole pattern of the opening and the free height above the tank beforehand.
- Run the sender's signal and ground wires directly to the display. With resistive senders, corroded terminals and a poor ground distort the signal.
- With the PCU, you collect several sensors tool-free at the Connect Hub; from there one cable runs to the display.
- Set sender type, tank volume and, for irregular tanks, the characteristic curve on the display. For the PCU: Setting up tanks on the PCU.
Tank gauge always shows full or empty
- Broken wire or missing ground: the display then sees a very high resistance and, depending on the curve, stays at full or empty. Measure at the sender: with a float sender, the resistance must change when the float moves.
- Wrong characteristic curve: besides 10 to 180 ohms, other ranges are in use, and some senders have the highest resistance when full, others the lowest. The gauge then runs backwards or sticks at the end stop.
- Float sticking: deposits in grey water slow down immersed parts.
- Pressure probe without the right density: with a water curve it permanently shows too little in a diesel tank.
- Ultrasonic in the wrong medium: the UTV is not suitable for fuel and heavily foaming liquids.
All tanks and the battery on one display
If you are retrofitting the tank gauge anyway, you can bring battery and devices onto the display at the same time. Which system type suits this is shown in Retrofitting a control panel.
Michael Kögel · Managing Director, philippi elektrische systeme GmbH
Michael Kögel is Managing Director of philippi elektrische systeme GmbH in Remseck am Neckar. Since 1978, the family-owned company has developed and manufactured on-board electrical systems for yachts, motorhomes and special vehicles.
Diplom-Ingenieur (Dipl.-Ing.), electrical engineering, with philippi for more than 35 years. Articles in the philippi Academy are written together with the engineering department and technically reviewed.
Published · Last reviewed
Related topics
Matching products. Order directly.
Control unit philippi Control Unit PCU with touch display
479,00 €
TGW water tank sender
from 126,70 €
TGT fuel tank sender
from 119,50 €
Ultrasonic tank sender UTV, contactless level measurement
115,00 €
Battery Tank Monitor BTM2
285,00 €Connect Hub – sensor hub for PCU and BTM2
79,00 €Frequently asked questions. Answered briefly.
Which tank gauge can I retrofit?
It depends on the tank sender. Float senders with 10 to 180 ohms suit most displays. The philippi tank senders connect directly to the BTM2 and VTM 2 monitors and the PCU, without an additional interface. If the battery should also be on the display, the BTM2 or PCU are suitable.
Why does my tank gauge always show full?
Often the signal wire is broken or the ground is missing. The display then sees a very high resistance and, depending on the curve, stays at full or empty. Also possible: sender and display use different resistance ranges, or the float is sticking. Measure at the sender whether the resistance changes when the float moves.
Can I show several tanks on one display?
Yes. The philippi PCU measures up to four tank senders and two temperature sensors directly at the display and also shows battery and energy flow. With the Connect Hub you connect all sensors at one point, and one cable runs to the display.
Read more. In the same subject area.
Shunt or BMS data: where the state of charge comes from
Zum Ladezustand führen zwei Wege: gerechnet aus dem Strom in der Minusleitung über einen Batteriemanagement-Shunt oder gemeldet aus dem Batteriemanagementsystem der Batterie. Eine BullTron-Batterie...
5 minReadFault Current Onboard: What the DCA2 Measures
Measured is the current flowing between the negative terminal of the onboard power system and the hull. The fault current monitor DCA2 detects this...
9 minReadSet alarm thresholds appropriately
Four to six thresholds suffice: low state of charge, low voltage, high voltage, battery temperature, and optionally black water tank and fresh water. The...
6 minReadTechnical
Your case isn't covered?
Ask us.
Our team knows every component and usually replies on the same working day, by email or by phone.