philippi 3.5-inch tank monitor VTM 2 for up to 4 tanks
philippi · Battery & Tank Monitors
Tank Monitor 3.5" VTM 2
The philippi 3.5" VTM 2 tank monitor shows up to 4 tanks and 2 battery banks on a 3.5" TFT touchscreen, for boats, yachts and expedition vehicles. It supports all philippi tank sensors and common third-party sensors, warns with an audible alarm at set limits and has a freely configurable, potential-free relay output. Operates on 12 and 24 V.
- 4 tank sensors connectable
- Touchscreen
In detail. Tank Monitor 3.5" VTM 2.
- Up to 4 tanks and 2 battery voltages in view at the same time, without pressing a button
- Compatible with all philippi tank sensors (TGT/TGW, UTV, TDS/TDN/TDT) and third-party sensors (10-180 Ω / 240-33 Ω / 0-3(10) V / 4-20 mA)
- Individual configuration per tank, including non-linear tank shapes
- Potential-free relay output with freely configurable function, e.g. for alarm messages
- Integrated brightness sensor dims automatically in the dark and saves energy
- Runs offline: own software, running locally on the display, without internet and independent of Android and iOS
The VTM 2 tank monitor is the further development of the digital philippi tank monitors and, compared with the smaller BTS-T, offers a fourth tank display and an additional potential-free relay output. For each connected tank sender, volume, tank type and sensor type can be stored in the setup; the level display can be adapted individually to non-rectangular tank shapes. If the set alarm thresholds for tank or battery voltage are exceeded or not reached, the VTM 2 reports this with an audible alarm that can be acknowledged.
Thanks to interval polling of the tank senders and the automatic power-save mode below 11.5 V / 23 V, the current draw of the VTM 2 stays low even in continuous operation.
The VTM 2 is compatible with all philippi tank sensors and suitable level sensors from other manufacturers. If you also need an NMEA 2000 connection, choose the BTM2 battery and tank monitor.
Original equipment quality
- Individually tested: every unit is connected and tested in a test environment in Remseck.
- Brand-name components, as in series production for boatyards.
- Repairable for decades: spare parts up to 30 years back, own repair centre.
Technical data
| Feature | Value |
|---|---|
| Display | 3.5" TFT colour touchscreen with brightness sensor |
| Display content | Tanks 1–4, configurable / 2 battery voltages |
| Suitable tank senders | Pressure probe, float sender, ultrasonic, flow sensor |
| Relay output | 1 potential-free contact, configurable function |
| Rated voltage | 12 / 24 V |
| Current draw | max. 80 mA @ 12 V, standby 14 mA |
| Dimensions | W 105 x H 105 x D 35 mm |
| Panel cut-out | W 88 x H 88 mm |
Manual
Read the manual onlineManufacturer and product safety
philippi elektrische systeme GmbH
Neckaraue 19
71686 Remseck am Neckar
Germany
info@philippi-online.de
Safety information: see the operating manual and data sheet.
Frequently asked questions. Answered briefly.
How many tanks can the VTM 2 monitor?
The VTM 2 monitors up to 4 tanks and also shows the voltage of 2 battery banks, all at the same time on one screen and without pressing a button. Volume, tank type and sensor type can be stored for each tank in the setup, including non-rectangular tank shapes. Compared with the smaller BTS-T, it offers a fourth tank display.
What can the relay output control?
The VTM 2 has a potential-free relay output whose function you configure freely; passing on alarm messages is typical. You set limits for tanks and battery voltage in the setup. If they are exceeded or not reached, the VTM 2 also reports this directly on the unit with an audible alarm that can be acknowledged.
Which tank senders can I connect?
All philippi tank sensors fit the VTM 2: the TGT and TGW immersion tube senders, the UTV ultrasonic sender and the TDS, TDN and TDT pressure probes. Sensors from other manufacturers with 10–180 Ω, 240–33 Ω, 0–3(10) V or 4–20 mA can also be used. This means the monitor also works with existing tank senders.
Does the VTM 2 have an NMEA 2000 interface?
No, the VTM 2 has no NMEA 2000 interface. If you also want to see tank and battery data on the chart plotter, choose the BTM2 battery and tank monitor. The VTM 2 works independently on 12 or 24 V, dims its display automatically via the brightness sensor and switches to power-save mode below 11.5 V or 23 V.
Related guides. Explained in depth.
Goes well with it. Accessories and add-ons.
Prefer a quick chat?
Tell us what you are planning. We will tell you honestly what you need and what you don’t.
