Balmar charging systems
The way to the right alternator.
In six steps.
This guide takes you in six steps to the right Balmar high-output alternator for your yacht: from the electrical load via battery technology and capacity to output, mounting type, belt and regulator. philippi is the official Balmar distributor in Germany and helps you choose.
Selection
Six steps. From the load to the charging system.
1Determine the electrical load
Accurate load calculations require a precise survey of your yacht's equipment. You will find the actual values in the device manuals, or you can ask a qualified marine electrician.
(Device load × duty cycle) × (number of devices) = total load
2Determine the battery bank
The capacity of the battery bank determines the size and type of alternator needed to keep the batteries healthy. Determine the technology and capacity of your battery bank:
- Standard and deep-cycle flooded batteries: charging at up to 25% of their capacity
- Gel batteries: up to 35%
- Standard AGM batteries: up to 40%
- TPPL and carbon foam AGM batteries: up to 100%
- Lithium batteries: very high charge acceptance, see the data sheet of the battery
(Battery capacity) × (charge rate) = maximum alternator output current. Your battery manufacturer specifies the recommended charging currents.
3Choose the alternator output
Knowing the technology and charging profile of the battery bank, you choose an alternator output that charges your bank optimally, together with a suitable multi-stage regulator and the temperature sensors.
For a current requirement of 70 A to 120 A, choose a 6-series alternator; for 170 A to 250 A, an XT-series alternator.
4Determine the mounting type
Determine how your existing alternator is mounted on the engine: the chosen high-output alternator must match this mounting. Marine alternators generally fall into one of four mounting types.
5Belt, pulley and AltMount
6 series from 70 A to 100 A: with single or dual V-belt pulley (Single Vee, Dual Vee) or serpentine pulley.
6 series from 120 A to 150 A: with dual V-belt or serpentine pulley.
XT series: with dual V-belt or serpentine pulley.
6-series alternators from 70 A to 100 A run with a simple ½-inch V-belt pulley. If you want to charge at more than 100 A, your engine needs a dual V-belt or serpentine belt system; if there is none, an AltMount conversion kit is required.
The XT series requires an AltMount conversion kit to a serpentine belt unless your engine already has a serpentine belt system.
6Choose additional options
Depending on the system, the charging system includes an external regulator such as ARS-5 or MC-618 (MC-624 for 24 V), temperature sensors for alternator and battery, a belt conversion kit and, on twin-engine installations, a Max Charge regulator kit. You'll find all components in the high-output alternators category.
High-output alternators. With regulator and accessories.
Balmar alternator 12 V 100 A for Volvo
from 816,00 €
Balmar alternator 12 V 120 A for Volvo
from 908,00 €
Balmar alternator 24 V 70 A for Volvo
from 1.007,00 €
24V-140A alternator for Volvo engines
1.810,00 €
Balmar alternator XT 12 V 170 A, single foot 1-2"
from 1.166,00 €
Balmar alternator XT 24 V 90 A, single foot 1-2"
from 1.219,00 €
Balmar alternator 12 V 100 A for Yanmar
from 816,00 €
Balmar alternator 12 V 120 A for Yanmar
from 908,00 €Frequently asked questions. Answered briefly.
Is my standard alternator sufficient for a lithium battery bank?
Usually not. It delivers too little current, its single-stage regulator misses the correct final voltage, and it is unprotected against load dump when the BMS disconnects. LiFePO4 also takes current until the regulator limits it, so the alternator runs flat out and overheats. You need an external regulator with temperature sensor and surge protection, often a DC-DC charger too.
Do I have to change the belt when upgrading to a more powerful alternator?
Above about 100 amps, a single V-belt is no longer enough: it slips, creates dust and wears quickly. A double V-belt or a multi-rib belt is then needed, on older engines together with a pulley conversion kit. This belongs in the planning, not the installation: a conversion kit is not an accessory you simply reorder.
Are there Balmar alternators for Volvo and Yanmar?
Yes. Volvo: 12 V with 100 or 120 A, 24 V with 70 or 140 A, plus a 12 V XT alternator with 250 A for D1/D2. Yanmar: 12 V with 100 or 120 A, 24 V with 70 A, series 94 for the 6LY and an XT version for common-rail engines. Pulley kits exist for both brands.
Advice
Questions about alternators?
We'll help you choose.
Every system has different requirements. We analyse your needs and put together the right charging system with you.