Supervision

Tank Monitor TCM 4V

The well readable digital tank monitor TCM 4V shows a clear overview of the filling level of up to four tanks, e.g. water, fuel and waste water tanks. Instead of 1-4 tanks it can supervise and display 1-3 tanks and 2 battery voltages. An over- and an undervoltage alarm can be set for both batteries individually. For the measuring of the liquid levels we recommend the proven high resolution immersion tubes TGT/TGW that are available in different lengths or for waste water tanks the ultrasonic sensors series UTV. The tank depth can be adjusted to the centimetre by using ultrasonic sensors UTV40 (tank depth equal or less than 40 cm) or UTV80 (from 40 to 80 cm). If you`re using a distance ring UTS to balance the off zone of the sensors, you can compensate this offzone - value too!

Older level sensors series TRG or level sensors with different characteristics (240-33 Ohm, 0-90 Ohm,...) can also be connected. Also you can use active tank sensors with current output 4 - 20 mA (hardware adjustment needed). For the volume metering of fresh water tanks the flow sensor DFS is exact to the litre. Also if there isn`t a possibility for an immersion tube or hole in the tank. The calculation of the level is made by a calculation of the taken water. After filling up the tank the shown filling level has to be adjusted in the setup.

The tank symbols, the tank volume and the connected sensors can be adjusted in the setup. The TCM can convert the measurement reading from a percentage display (%) to a litre display (l). Please keep in mind that because of the limited resolution of the sensors, the shown liters / level will never be exact (exception: flow sensor DFS). To adjust the displayed level to non-rectangular tanks, a correction/ compensation factor can be set in the setup for each tank. An interval measurement procedure reduces the energy consumption of the system to a minimum. An alarm buzzer with an acknowledge function advise about the tank level coming out of a limit. The threshold level can be set in the setup menu.

Ultrasonic sensor UTV, immersion tubes TGT, TGW, TRS and flow sensor DFS have to be ordered separately.

GWA

GWA

Adapter flange for the installation of tank sensors TGT /TGW to a given screw-hole circle matching the SAE-norm. incl. are gasket and screws.

Built-on height: 18 mm


GWA Order-no.: 660109010



Info

TDS 200

TDS200 TDN200 TDS TDW TDN

Pressure sensor TDS / TDN for the most precise and reliable tank level measuring! the pressure sensor tDS will be submerged to the bottom of the tank. the current tank level is being measured via the hydrostatic pressure of the liquid.

  • TDS: this sensor is suitable for diesel, water, grey & waste water tanks, but nor for petrol, kerosine, petroleum (EEX-zone). Very precise and reliable measurement at a very high solution (under 1cm),also at swell.
  • TDN: this sensor is suitable for water, grey & waste water tanks, but not for diesel, petrol, kerosine, petroleum (EEX-zone). Very precise and reliable measurement at a very high solution (under 1cm),also at swell.
  • In scope of delivery there`s a mounting flange (Ø 79 mm) with different screw hold circles (matching TGt and SAE) and PG-fitting and if needed we can deliver a guide tube for the mechanical guidance.

As monitor for the pressure sensor TDS you can use our tank monitors TCS / BTM (TCM 4V) or the System monitor PSM2 (through the tank interface CMT 2). Analog gauges cannot be used.
Attention: the TCM4V needs a hardware modification „4 - 20 mA“!


TDS 200 Order-no.: 660261206


TDW 200 Order-no.: 660251208



Info Manual

TCM 4V

TCM4V TCM4 TCM

Number of tanks: 1-4 or 1-3 tanks and 2 battery voltages

 

  • Flow sensors DFS possible: 1-2
  • Tanksensors TGT/TGW/UTV possible: 1-4
  • Alarmfunction tank: Empty- / fullalarm
  • Alarmfunction battery: under- / overvoltagealarm
  • The tank depth can be adjusted to the centimetre by using ultrasonic sensors UTV40 or UTV80.

    • If you`re using a distance ring to balance the off zone of the sensors, you can compensate this value too!

Dimensions: W 105 x L 105 x D 40 mm

Installation cutout: 88 x 88 mm


TCM 4V Order-no.: 080001410



Info Manual

TCS

TCS TCM

The Tank Monitor TCS is a compact tank monitoring system for yachts and vehicles with up to 3 tanks. In parallel, two battery groups can be monitoredfor voltage. The 2.4" TFT touch screen shows at a glance the tank levels and the voltages of the batteries without having to operate a button. The built-inambient light sensor automatically dims the screen in the dark and saves valuable energy.All known philippi tank sensors such as TGT / TGW, UTV, TDS / TDW can be connected, also existing third-party tank sensors with the signals 10-180Ω / 240-33 Ω / 0-5 V / 4-20 mA are possible. Each tank can be configured individually, and adaptation to non-linear tank geometries is also possible.For monitoring, individual minimum or maximum alarm thresholds per tank can be defined.

Dimension: W 105mm x H 75mm x D 40mm


TCS Order-no.: 071003040