Supervision

Battery monitors BLS / BTM

 

For monitoring the battery system, we offer battery monitors in two screen sizes, 2.4" and 3.5" full color touch monitors. These allow the exact charge level of the service battery to be read off at any time. In addition, all relevant battery data such as current, voltage, remaining capacity and remaining operating time of the on-board battery as well as the voltage of two additional starter battery groups can be read off. In addition, data on battery usage such as mean discharge depth, battery capacity no longer usable and the number of charge/discharge cycles are recorded.
If the service battery falls below the adjustable capacity threshold or the additional batteries fall below the adjustable voltage thresholds, an acoustic alarm sounds and a corresponding warning message appears on the display.


  • Very high accuracy (max. 10mA) and wide measuring range (10 mA - 300 A or 600 A)
  • automatic battery full recognition and correction of the charging factor
  • Tracking of the effective battery capacity during cyclic operation
  • Detailed information about the use of the battery such as number of charge cycles and deep discharges, average depth of discharge
  • can be used for all nominal battery voltages (12V/24V), also in mixed configuration if e.g. the starter battery is 24V and the vehicle electrical system is 12V.

BTM

BTM

The combined digital battery and tank monitor BTM is the successor of the well-known and successful battery monitor series BCM and the tank monitor series TCM.  It`s 3.5-inch color touch-screen graphic display provides an overview of the battery system status and the level of up to four tanks and shows the status of the ACE charger during operation.  It allows the connection of a battery shunt SHE 300 for battery  monitoring, the direct connection of 4 tank sensors and the connection of an automatic charger ACE via the interface ACE-LIN.  Suitable for all battery types such as acid, GEL, AGM and LiFePO4.

 

The tank sensors, the shunt "SHE 300" and the interface to the charger "ACELIN" must be ordered separately!

 

Please download the latest software

Quick guide to update the monitor and shunt

 

 

Operation voltage:                                   8-32 V

Consumption:                                          max. 70 mA @ 12V, Stand-by: 6 mA

Dimensions:                                             L 105 x W 105 x H 35 mm

Cut-out:                                                   88 x 88 mm


BTM Order-no.: 071004000



Info

BLS-Set

BLS-Set / BLS

The Battery Monitor BLS is a compact battery monitor for battery systems consisting of a 12/24 V starter battery and one or more 12/24 V house batteries connected in parallel. The 2.4" TFT touch screen displays all important data of the entire battery system at a glance without the need  to press a button. The built-in brightness sensor automatically dims  the screen at night, saving valuable energy.
 . Display of the current voltage, the current charge or discharge current, the remaining time, the battery temperature and the state of charge of the consumer battery(s)

. Further information on the use of the consumer battery(s): No. of charge cycles, deep discharges & mean depth of discharge.

. Warning of a dangerous deep discharge by an adjustable acoustic alarm
. Suitable for all battery types like acid, GEL, AGM and LiFePO4

 

The shunt SHE 300 is included in the scope of delivery of the BLS.

 

Please download the latest software

Quick guide to update the monitor and shunt

 

Rated Voltage:                          12 V

Consumption:                           max. 50 mA @ 12V, Stand-by: 6 mA

Dimensions:                             W 105 x H 75 x D 28 mm

Cut-out:                                   87 x 65 mm

Current rating:                         300A, 600A 1min, 1500A 0,5s


BLS-Set Order-no.: 071003210



Info Manual

BLS-Set Plus

BLS / BLS Set Plus / BLS Set

Battery Monitor BLS for displaying a 12/24V house and a 12/24V starter battery. 2.4" TFT colour touch screen graphic display with brightness sensor.  

 

Expand the BLS monitor by connecting an ACE series  charger to create a fully-fledged Battery charge management system:

The ACE-LIN interface integrated into the automatic charger enables the BLS battery monitor to monitor and control the charging process of the ACE automatic charger to optimise charging. The display also shows the AC mains voltage, the active charging phase, the battery temperature, the charging voltage and the charging current. The charging power can be reduced or the silent mode (fan off) activated at the touch of a button. A temperature alarm, for example, can be defined for further charge monitoring.

 

The shunt SHE 300 and the interface ACE-LIN are included in the scope of delivery of the BLS-Set Plus.

 

Rated Voltage:                         12 V

Consumption:                           max. 50 mA @ 12V, Stand-by: 6 mA

Dimensions:                             W 105 x H 75 x D 28 mm

Cut-out:                                   87 x 65 mm

Current rating:                         300A, 600A 1min, 1500A 0,5s


BLS-Set Plus Order-no.: 071003220



Info Manual

SHE 300

SHE300 SHA SHE

Digital battery management shunt for installation in the negative line of the house battery.

The SHE 300 shunt is compatible with the BTM and BLS monitors.

The shunt is powered via the consumer battery's voltage measuring line. 

 

Suitable for continuous charging or discharging currents up to  300 A and battery capacities up to 1000 Ah

 

Rated current:           300A, 600A 1min, 1500A 0,5s

Consumption:            10 mA@12 V, 5 mA@24 V

Operation voltage:    DC 8-40 V

Current range:          10 mA - 1500 A

Connection:               Bolts M8

Dimensions:              L 118 x W 40 x H 65 mm


SHE 300 Order-no.: 070030300



Info

SAS 4

SAS4 SAS

This bus bar will be attached directly on the shunt  SHC 612 to connect smaller lugs / lines  (M12, 2x M10, M8).
 
Dimensions: L 140 x W 30 x H 30 mm


SAS 4 Order-no.: 080009014



Info

BTM2

BTM / BTM2

Batterie-, Tank und Lade-Monitor BTM 2. Intuitives, 3,5“ Farb-TFT-Touchscreen-Grafikdisplay   mit   Helligkeitssensor   zur   automatischen   Anpassung   der   Displayhelligkeit. Incl. NMEA 2000 Schnittstelle.

 

Die Tanksensoren, der Shunt "SHE300", das Ladegerät-Interface „ACE-LIN“ und das NMEA 2000 Anschlusskabel “N2K-Kabel” müssen separat bestellt werden.

 

Betriebsspannung:                                  8-64 V

Stromaufnahme:                                     max. 70 mA @ 12V, Stand-by: 6 mA

Abmessungen:                                         L 105 x B 105 x H 35 mm

Einbauausschnitt:                                    88 x 88 mm


BTM2 Order-no.: 071004050



Info

LTM

LTM

Lithium-Batterie Tank Monitor LTM

Batterie-, Tank und Lade-Monitor LTM. Intuitives, 3,5" Farb-TFT-Touchscreen-Grafikdisplay mit Helligkeitssensor zur automatischen Anpassung der Displayhelligkeit.

 

Die optionalen Tanksensoren, der Shunt "SHE 300", das Ladegerät-Interface „ACE-LIN“ müssen separat bestellt werden!

 

Betriebsspannung:                                  8-64 V

Stromaufnahme:                                     max. 70 mA @ 12V, Stand-by: 6 mA

Abmessungen:                                         L 105 x B 105 x H 35 mm

Einbauausschnitt:                                    88 x 88 mm


LTM Order-no.: 071004320



Info

Smart Shunt

Smart Shunt 12-48V DC

350A Dauerbelastung

zur Erweiterung eines Balmar Smart Shunt Netzwerkes zur Überwachung von Verbrauchern, Ladequellen und zum Energiemanagement.


SG2-0100 Order-no.: 755020100



Bluetooth und Monitoring Shunt

Bluetooth und Monitoring Shunt für Balmar Lichtmaschinen und Batterien

Shunt mit Bluetooth Schnittstelle zur Überwachung und Konfiguration der Balmar Lichtmaschinen oder als Batterie Monitor für Verbraucher Batterien, Solar, Wind und andere Ladequellen.

Alle Daten können am Smartphone angezeigt werden.

Es können mehrere Smart Shunts zu einem Netzwerk verbunden werden.

Damit ist eine Überwachug der kompletten elektrischen Verbraucher per Bluetoothverbingung und Smartphone möglich.


SG205 Order-no.: 755020500



ACE-LIN

ACE-LIN ACE

The ACE-LIN interface enables ACE chargers to communicate with BTM and BLS monitors. The interface is put into operation by clipping it into the prepared holder in the ACE charger and plugging in the  connecting cable.  
 
The ACE-LIN interface is only required for the ACE 12/25, ACE 12/40 and ACE 24/20 models. All other models already have an interface.

 

 


ACE-LIN Order-no.: 080004975



Info

BLM-Set

BLM, BLM-set / BLM SET

All information about the battery system at a glance and if needed on your plotter via the NMEA 2000/Seatalk NG interface.
Monitoring of the consumer and starter battery via the shunt SHE 300 (included). Optional voltage monitoring of a third battery group.
n By means of an additional shunt SHP 300 the power and the energy yield of a solar system can be read.
n Display of charging current and mains voltage when using one of our ACE battery chargers.
n Effective protection against deep discharge and capacity-dependent energy management via the remotely controllable battery main switch FBR 265.

Available as of June 2021

Operation voltage:                                   8-32 V

Consumption:                                          max. 70 mA @ 12V, Stand-by: 6 mA

Dimensions:                                             L 105 x W 105 x H 35 mm

Cut-out:                                                   88 x 88 mm


BLM-Set Order-no.: 071004210



Info